Water Heater Installation – Plumbing Bend OR

In an perfect world, the very best time for a water heater installation would be when your old one is still working and you have plenty of time and money to get a brand-new one. Of course, this is rarely the instance, and possibilities are your old, corroded heating unit will quit in the middle of a cool winter’s evening. When this occurs, the most effective choice is to call an expert. Water heaters are not a DIY home owner task. Electricity, gas and water are not for the inexperienced. Most communities even require a permit & inspection. Your Deschutes Plumbing Company plumber can address the considerable safety and code issues involved and protect your home and family by ensuring you have a safe, reliable appliance.

When selecting your substitute water heater, make sure you select the very same fuel type (gas or electric.) This may seem obvious, however you ‘d be stunned at the number of folks who do not make that distinction before buying. If you would like to alter the size, however, you could definitely do that. For example, if you had a 40 gallon tank, but want to raise to a 50 gallon, this is completely acceptable. Simply see to it you have more than enough clearance in between the wall and the heater.

Before New Water Heater Installation

Before you take out the old water heater, measure the size in between the hot and cold pipes on the top of the heating system. Try to make sure that the new one has the very same measurements, or as close as possible.

Examine the plumbing system to make certain there is a gas union (for gas heaters), and guarantee that there is a cold water shutoff inlet pipe, as well as a union connector for the warm water outlet pipe. The majority of plumbing professionals make sure this is all in place when mounting water heating units, so be sure you have everything in position.

When your brand-new water heater arrives, make certain that you have the required tools and workforce to get it where it has to go (typically in the basement.) This might require leasing a device dolly, and rewarding at the very least one friend to assist you.

Before doing anything, you need to turn off the utilities connecting to the water heater. Shut down the major water that encounters the alreadying existing heater. If you have a power heating unit, switch off the energy that runs to the heating unit by eliminating the fuse or disabling the circuit breaker that runs to the heater. If it is gas powered, guarantee that the pilot burner is out after you shut down the gas shutoff.

Draining the Tank

The moment the water has actually been turned off, you’ll need to drain the old water heater tank just before eliminating it. There are numerous actions involved in doing this:.

  • Open the hot water tap that is closest to the heating system.
  •  Attach a hose to the shutoff on valve on the water heater.
  • Place the opposite end of the hose on a floor drainpipe.
  • Open the valve slowly, so the drain doesn’t block with sediment that may be present.

Equipment Needed

You will certainly need the following equipment in order to disconnect your old water heater, switch off the utilities and complete the set up and new water heater installation.

  • Tongue and groove pliers.
  • Pipe wrench.
  • Slip joint pliers.

Once the water lines, power or gas service, and flue have been disconnected, the old water heater is ready to be taken out. To do this, comply with these actions:.

  • Move the old water heater onto a cart (you might have to have a close friend help you with this).
  • Clean the floor where the old water heater was.
  • Move the brand-new unit to where the old device was; make sure to line points up with the already existing plumbing system pipes.
  • Use a level to make certain that the new device is safely in place, and not on an angle.

Install the New Fittings

water heater installation Bend ORSince you have the brand-new water heater in position, you’ll need to set up the different installations. These include the temperature valve, pressure relief valve, and the discharge drain water pipes. Read the manufacturer’s guidelines meticulously when setting up these installations. For copper, make certain to use Teflon tape; for galvanized installations, use joint compound or water pipes dope.

Next, you’ll have to install the plumbing system lines. If the new electrical outlets do not line up specifically with the old ones, make use of versatile copper lines to ensure things line up appropriately. If you don’t already have the cold water shut off valve, set up one, per manufacturer’s directions.

After the water lines have been installed, it’s time to connect the fuel source. If you have a gas heating unit, connect the gas burner control valve to the gas line. Check for leaks by switching on the gas valve and applying a soapy remedy onto the union and joints. If you view bubbles, you’ll have to tighten the connections; if you can not tighten it you will have to call the gas company and/or an expert plumbing contractor. If there are no leaks, you can then connect the flue. For electrical heaters, hook up the ground wire and power lines to the junction box.

Since all the hookups have been made, and utilities have been turned on, it’s time to fill the tank with cold water, and turn on the new water heater. The main water supply ought to now be turned on, and the pilot light ought to be lit, if it’s a gas water heater. The thermostat on the unit needs to be set in between 110 and 130 degrees Fahrenheit.

Basic Water Heater Maintenance

It is always a good idea to have an assessment of your heater at the very least annually. For best outcomes, hire an expert. If you are doing the assessment on your own, ensure you check for rust or rust of the pipes to name a few things. Inspect for gas leaks (if a gas water heater) and for worn away wiring, which could be a fire danger.


Deschutes Plumbing Company, LLC © 2019 All Rights . 841 NW Bond Street, Bend, OR 97701 . Contact Us . Terms of Service . Privacy Policy